Cheshire Cat Computing

Hi,

Has anybody experienced the following error message?

cannot find RRDs.pm in /usr/lib/perl5/site_perl/5.8.6/i386-linux-thread-multi /usr/lib/perl5/site_perl/5.8.5/i386-linux-thread-multi /usr/lib/perl5/site_perl/5.8.4/i386-linux-thread-multi /usr/lib/perl5/site_perl/5.8.3/i386-linux-thread-multi /usr/lib/perl5/site_perl/5.8.6 /usr/lib/perl5/site_perl/5.8.5 /usr/lib/perl5/site_perl/5.8.4 /usr/lib/perl5/site_perl/5.8.3 /usr/lib/perl5/site_perl /usr/lib/perl5/vendor_perl/5.8.6/i386-linux-thread-multi /usr/lib/perl5/vendor_perl/5.8.5/i386-linux-thread-multi /usr/lib/perl5/vendor_perl/5.8.4/i386-linux-thread-multi /usr/lib/perl5/vendor_perl/5.8.3/i386-linux-thread-multi /usr/lib/perl5/vendor_perl/5.8.6 /usr/lib/perl5/vendor_perl/5.8.5 /usr/lib/perl5/vendor_perl/5.8.4 /usr/lib/perl5/vendor_perl/5.8.3 /usr/lib/perl5/vendor_perl /usr/lib/perl5/5.8.6/i386-linux-thread-multi /usr/lib/perl5/5.8.6 .

Tried the following;
- make site-perl-install
- reinstall rrdtools
- perl installed under /usr/bin/perl
- check this intructions; http://www.steveshipway.org/software/rrd/doc/PROBLEMS

cfgmaker;

cfgmaker --global "WorkDir: /var/www/html/mrgt" \
--global "Options[_]: growright,bits" \
--ifref=descr \
--ifdesc=alias \
public@192.168.30.1 \
public@192.168.30.2 \
--global "Options[_]: growright" \
--ifref=name \
--ifdesc=descr \
public@192.168.30.3 \
--ifdesc=name \
public@192.168.30.4 > mrtg.cfg

*.cfg created OK
but no RD files under specified location?

Thanks for any inputs.

DDemirchi

_________________
Steve Shipway
UNIX Systems, ITSS, University of Auckland, NZ
Woe unto them that rise up early in the morning... -- Isaiah 5:11

Steve,

I passed RRDs.pm but I can't see any graphics (switch information)
When you select the switch/router. I only see the following;
Traffic Analysis for 192.168.1.109 -- ddc2924
Last update: Sat Feb 4 09:19:46 2006

*.cfg:
./cfgmaker --global 'WorkDir: /var/www/mrtg' \
--global 'Options[_]: bits,growright' \
--global 'LogFormat: rrdtool' \
--global 'PathAdd: /usr/local/rrdtool-1.2.11/bin/' \
--global 'LibAdd: /usr/local/rrdtool-1.2.11/lib/perl/5.8.6/i386-linux-thread-multi/' \
--output /var/www/mrtg/cfg/192.168.1.109.cfg \
--ifref=ip \
community_info@192.168.1.109
File Created under: /var/www/mrtg/cfg/192.168.1.109.cfg / OK
*.rrd:
env LANG=C /usr/local/mrtg-2/bin/mrtg /var/www/mrtg/cfg/*.cfg
File created under; /var/www/mrtg/192.168.1.109_192.168.1.109.rrd / OK


routers2.conf - checked configuration/modified as needed: / OK
==============
If I ran only
./cfgmaker --global 'WorkDir: /var/www/mrtg' \
--global 'Options[_]: bits,growright' \
& update;
files created under /var/www/mrgt/ and can see graphic.

Any suggestions, what am I doing wrong?

Thanks for any inputs!

DDemirchi
-almost there

Which files are you looking at?

Remember, if you run MRTG in native mode, it creates .gif, .html and .log files. If you run in rrdtool mode, then it only creates .rrd files. You need to use routers2 frontend (or one of the other frontends) to view the graphs, which are only created on the fly by the frontend. If you're looking for web pages created by mrtg, you wont find any.

If you're getting broken images when trying to view the routers2 pages, tell me what error messages are being printed on screen

_________________
Steve Shipway
UNIX Systems, ITSS, University of Auckland, NZ
Woe unto them that rise up early in the morning... -- Isaiah 5:11

Hi Steve,

Thank you, Thank you and Thank you very much!
I can see all the *.png outputs files.

Now I need to figure out some of the advanced features of your application

Thanks again!

DDemirchi